A fast drying reputation isn’t all Intercure® HS is renowned for. Complete with MIO, this primer/intermediate can improve your productivity and lower your. Allow appropriate loss factors. Airless Spray, Air Spray, Brush, Roller. PRACTICAL. INFORMATION FOR. INTERCURE Colour. Gloss Level. Volume Solids. A fast drying reputation isn’t all International Intercure HS is renowned for. Complete with MIO, this Fast cure anti-corrosive primer/intermediate with added.
|Published (Last):||26 November 2010|
|PDF File Size:||14.70 Mb|
|ePub File Size:||1.70 Mb|
|Price:||Free* [*Free Regsitration Required]|
The surface may deteriorate to Sa2 standard but must be free from loose powdery deposits. Each product clause is authored in Hz format and is intended for inclusion in project specifications.
At low temperatures, it may be necessary to thin Intercure HS to enable airless apray application to be performed. Suitable for overcoating within seven hours in most climatic conditions.
INTERCURE HS – SAND (KIT / 4G) – L
I would like to hear about offers and services: Not intended for use as a primer for steelwork which may be subjected to continuous immersion conditions. A fast drying reputation isn’t all International Intercure HS is renowned for.
It is good working practice to periodically flush out spray equipment during the course of the working day. Over-application of Intercure HS will extend both the minimum overcoating periods and handling times, and may be detrimental to long term overcoating properties.
Typical Coverage per coat 5. Additionally, in common with all integcure Intercure HS will chalk on exterior exposure. Work stoppages Do not allow material to remain in hoses, gun or spray equipment.
The figures stated above are approximate.
Other content by this manufacturer: Prior to paint application, intercyre surfaces should be assessed and treated in accordance with ISO International Paint Ltd Web: VOC values are typical and are provided for guidance purpose only. Excessive over application of material on areas such as poorly prepared welds may result in long term stress cracking and so early failure. However, if necessary, application over prefabrication blast primers can be performed.
Surface preparation All surfaces to be coated should be clean, dry and free from contamination.
International Intercure HS Reference: Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays. We recommend that Customer first purchases the smallest Product available or access an industry standard colour chart in person and not digitally to ensure that the colour is acceptable for its purposes.
As a primer for steelwork intended for use in a wide range of environmental conditions including offshore, chemical and petrochemical plants, industrial buildings, pulp and paper mills, power plants and bridges. Your browser does not support automatic copy to clipboard.
Offers excellent barrier protection, low temperature cure and rapid overcoating properties. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. Consult International Protective Coatings for further details.
Intercure® HS – International Paint Ltd
Warning Intercure HS is preferred for use with systems for chemical environments where zinc intefcure materials can be subject to attack in both acidic and alkaline conditions.
Provides intercuee cure even at low temperatures often encountered in maintenance painting. Absolute measured adhesion of topcoats to aged Intercure HS is less than that to fresh material, however, it is adequate for the specified end use.
Once the unit has been mixed, it must be used within the working pot life specified. The content of this website is our best recommendation and is not advice. However, if necessary, application over prefabrication blast primers can be performed. Intercure HS will normally be applied to suitably prepared steel, e.
Thoroughly flush all equipment with International GTA It is your responsibility to read the Product Data Sheets available below before you place an order and prior to application of the product.
As a primer for steelwork intended for use in a wide range of environmental conditions including offshore, chemical and petrochemical plants, industrial buildings, pulp and paper mills, power plants and bridges.
This product must only be thinned using recommended International GTA thinners. Always mix a complete unit in the proportions supplied. Typical Coverage per coat. If oxidation has occurred between blasting and application of Intercure HS the surface should be reblasted to the specified visual standard.