A. ASTM F is for inch-based fasteners and ASTM FM is for metric fasteners, although the designations are identical between the two. The fastener industry should be made aware of an important recent development in the realm of. ASTM fastener standard specifications. ASTM F/. ASTM F/FM: Standard Specification for Electrodeposited Coatings on Mechanical Fasteners, Inch and Metric.

Author: Tauk Megor
Country: Yemen
Language: English (Spanish)
Genre: Finance
Published (Last): 7 June 2014
Pages: 233
PDF File Size: 5.93 Mb
ePub File Size: 9.42 Mb
ISBN: 345-4-24150-732-8
Downloads: 33783
Price: Free* [*Free Regsitration Required]
Uploader: Kazrazahn

The external thread allowance may thus be used to accommodate the coating thickness on threaded fasteners, provided the maximum coating thickness is no more than 1? The average current density is usually low enough such that the extremity-to-center coating thickness ratio is much lower than with barrel-plating.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not 1f941m as part of the standard. Link to Active This link will always route to the current Active version of the standard. For internally threaded fasteners barrel-plating is generally suitable.

In this process, quantities of an item are placed within a containment vessel, called a barrel. The external thread damage is also minimized in comparison to barrel-plating due to the absence of tumbling. Is there an acceptable way to demonstrate equivalence? The cascading action randomly exposes the surface of each individual piece to the process electrodes while also maintaining electrical continuity between all f19441m the parts.

All I want is a single spec to call out, to get the basic zinc-electroplated fastener. Combining values from the two systems may result in non-conformance with the standard. Baking to relieve hydrogen embrittlement must be performed prior to the application of the chromate?

It specifies coating thickness, supplementary hexavalent chromate or trivalent chromite finishes, corrosion resistance, precautions for managing the risk of hydrogen embrittlement and hydrogen embrittlement relief for high-strength and surface-hardened fasteners. It assumes that the external thread pitch diameter is at the maximum and that the internal thread pitch diameter is at the minimum zstm the tolerance see Fig. Historical Version s – view previous versions of standard.

  APLASIE MEDULAIRE PDF

ASTM / ASME spec F1941 for Zinc Plating … Which finish to choose?

All information presented is for general reference and does not represent a professional opinion nor the policy of an author’s employer. See Section 10 and Appendix X1. The test plan should be designed based upon the speci?

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. As the barrel is moved through the process steps, it is also rotated such that the individual items are constantly cascading over one satm.

ASTM F1941

ASTM International takes no position respecting the validity of any patent rights asserted in connection with asrm item mentioned in this standard. The barrel is designed to move the group of items, together, through each of the process steps, allowing ready ingress and egress of processing solutions and rinses.

This specification covers application, performance and dimensional requirements for electrodeposited coatings on threaded fasteners with metric screw threads. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

ASTM / ASME spec F for Zinc Plating Which finish to choose?

The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Toby — Thanks for boiling it down for me. I am getting really confused in the finishing section. It should be noted that modi?

ASTM F – Portland Bolt

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. A number in parentheses indicates the year of last reapproval. In this process, quantities of aastm item are placed on a support, called a rack.

If heavier coatings are required allowance for the deposit buildup must be made during the manufacture of fasteners. One of these should meet your needs. Last previous edition F — It specifies coating thickness, supplementary hexavalent chromate or trivalent chromite finishes, corrosion resistance, precautions g1941m managing the risk of hydrogen embrittlement and hydrogen embrittlement relief for high-strength and surface-hardened fasteners.

  DZIEJE FILOZOFII ZACHODU RUSSELL PDF

Originally published as F — The chromate finish letter E designates a black color. In some of the process steps, notably the electrocleaning and electroplating steps, an electric current is applied to the group of items.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The local coating thickness on a part is a result of the electrical current density at that location. NOTE 2—With proper care many steel fasteners can be plated without baking by correlating process conditions to the susceptibility of the fastener material to hydrogen embrittlement, and by applying adequate process control procedures, such as those outlined in Appendix X4.

We do not specify specific plating specs; we simply use the general name. It’s not possible to diagnose a finishing problem or r1941m hazards of an operation via these pages.

December 9, Q. With normal methods for depositing metallic coatings from aqueous solutions, there is a risk of delayed failure due to hydrogen embrittlement for case hardened fasteners and fasteners having a hardness 40 HRC or above. It also highlights the differences between barrel and rack plating and makes recommendations as to the applicability of each process.

F — 00 Standard Speci? My research is leading me to believe that ASTM F M both inch and metric are the two standards I need; but even those have over grades listed!

Corrosion resistance and embrittlement of coatings shall be determined by performing mechanical tests. The electrodeposited coating shall cover all surfaces and shall meet the following requirements: f941m