The 3G3JX Inverter meets the EC Directives and UL/cUL standard frequency limit, Frequency jump, Curve acceleration/deceleration, Manual torque boost. The [email protected]@@ terminal symbols are shown in brackets. 㸨2. Connect a For detail of Inverter selection, refer to the JX series User’s Manual. ( TYPE [email protected] Model X Series Inverter. Thank you for purchasing JX inverter. To ensure safe operation, please be sure to read the safety precautions .
|Published (Last):||25 January 2011|
|PDF File Size:||7.60 Mb|
|ePub File Size:||14.63 Mb|
|Price:||Free* [*Free Regsitration Required]|
Frequency Addition Function Function Mode Operation Frequency Function This function makes calculations for two inputs and reflects the result as the output frequency.
Hang the upper side on the hooks. Function name Data Default setting Unit Loosen the front cover mounting screw. Be careful, especially if you set a base frequency at below 50 Mahual.
OMRON 3G3JX USER MANUAL Pdf Download.
This helps prevent data rewrite due to erroneous operation. FA1 constant speed arrival signal Multi-function Page Options RV reverse C input 1 selection Specified data has an unacceptable format. Network error Network error LOG: Disabled stop function at b 3g3hx to C contact selection are excluded. Page Function Mode Register Parameter Function name Monitor or mznual range Resolution Function Multi-function input 3g3ux h C selection 2nd 33jx input 1 h C selection Multi-function input 2 h C selection Digital Operator F 2nd frequency Page Function Mode Function code Maximum number of data Maximum data number in 1 Function code Function bytes in 1 message message Coil status reading 32 coils in bits Holding register content reading 4 registers in bytes Writing into the coil 1 coil in bits Writing into holding register 1 registers in bytes Page Function Mode Message configuration: Control Devices Division H.
Displays in increments of 0. With this key, you can always change the display as follows. The Inverter does not allow this function.
Omron 3G3JX User Manual (Page of )
Undervoltage Appears when the Inverter is in the undervoltage standby condition or standby with the power shut off. Trip after frequency matching deceleration stop Allowable b The default setting is sink logic. Connect a noise filter to the output side of the Inverter to reduce induction and radio noise.
Be sure to set the parameters shown below. Factory Manhal Change the A setting.
Omron 3G3JX User Manual Page 197
Maual cannot set analog inputs FV and FI to both target and feedback values simultaneously. It may represent the result of OMRON’s test conditions, and the users must correlate it to actual application requirements.
For details on the operation and settings, refer to maanual Operation” page Electrical specifications Output terminal Resistance load Inductive load Max. Frequency pull-in restart Do not connect the signal lines for inputs FV and FI simultaneously. Page 65 Operation Procedure Example: This function automatically keeps DC voltage at the set level during deceleration.
Omron 3G3JX User Manual
Data is not stored by pressing the Mode key. To use this function, set the DC injection braking selection A to Should you find any problems with the product, immediately contact your nearest local sales representative or OMRON sales office. For other methods, refer to the [A] section in “Frequency Reference Selection” Output current monitor 3g3mx securely to the ground as specified type-D grounding for V class, and type-C grounding for V class.
3g3nx To print the manual completely, please, download it. Page 43 Connect a noise filter to the output side of the Inverter to reduce induction and radio noise. Page 33 Wiring Note 2: The code of the basic function mode is displayed as “F”. The information provided here is vital to safety.
Output frequency monitor 3gg3jx Not doing so may result in a serious injury due to an electric shock. This helps display the actual physical value on the monitor. Specified address does not exist.
If a parameter for an extended function code is stored after pressing the Enter key, however, that code A, b, C, d, or H appears at the next power-on. Table Of Contents Contents Introduction